Weight Stack Plates & Bushings

Use this Rubber slide on Weight to adjustment your poundage ! Move up in 5 pound increments.

Adjust your lifts in 2.5 pound increments with this rubber adjustment shoe for your weight stack.

Rubber Weight Add-on Weight. of 7.5 lb Rubber Coated. One Slot

Rubber Add-on Weight. 2.5 lb Rubber Coated. Two Slot

Rubber Add-on Weight. 5 lb Rubber Coated. Two Slot

Keep those plates from breaking or keep the noise down, with these rubber plate separators.

Chrome Weight Adjustment Plate 5 Pounds, Slides onto the weight stack selector rod.

Chrome Weight Adjustment Plate 2.5 Pounds, Slides onto the weight stack selector rod.

Ring Selector Rod. 15 Plates plus the top plate. "o" Bolt is optional, and does not come with this unit. Can be ordered Separately.

Ring Selector Rod. 20 Plates plus the top plate.

Ring Selector Rod. 30 Plates plus the top plate.

Chrome Top Plate for your Home Gym.

CAST IRON Top Plate for your Home Gym.

Change out some of those tens and replace them with 5's. Move up in five pounds increments. Size = 3.5 in W X 7 5/8 inches Long. Whole is 1 5/16th in. from end of plate to center of first whole. Each whole will accept 1 in. guide rod.Measurements are approximately.

Ten Pound Weight plates. Replace those broken plates with these 10 pounders.Size = 4 11/16 in W X 10 1/8 inches Long. Whole is 2 9/16th in. from end of plate to center of first whole. Each whole will accept 1 in. guide rod.Measurements are approximately.

Make that weight stack heavier with these 15 pounders.Size = 6 7/8 in W X 10 1/4 inches Long. Whole is 2 11/16th in. from end of plate to center of first whole. Each whole will accept 1 in. guide rod.Measurements are approximately.

Make that weight stack heavy by using these 20 pounders. If you have a twenty whole rod, then you can increase that stack to 20 x 20 = 400 pounds, without any lost of range of motion.Size = 8 3/4 in W X 10 3/16 inches Long. Whole is 2 9/16th in. from end of plate to center of first whole. Each whole will accept 1 in. guide rod. Measurements are approximately.

Plastic Weight plate bushings. Snap-in design. Fits one inche weight rods for weight stacks. Price is each...... Min. Order is $ 10.00 ( Discount available for orders of 200 pcs or more )

150lb stack comes with 14 x 10 lb. plates + Selector bar + Top Brick + Sector Pin - . ( Due to changing prices, please call to verify current price for weights. Top Chrome Plate not included.

200lb stack comes with 19 - 10lb. Select plates + Selector rod + Top plate + Sector Pin - . Top plates not included.

300lb stack comes with 29 - 10lb. Select plates + Selector bar + Top Brick + Sector Pin - Top plates not included.

Steel top quality commercial weight stacks, powder coasted, balanced, fully machined surfaces. Size: 4 inch x 1 inch thick with 1 inch diameter holes. 100 pound stack in 10 pound plates, with standard 7/8 inch shaft, heavy duty spring cotter pin, high tensil laniard locking pin and 1 inch thick powder coard steel (not cast) weight plates, with press-in bushings and fits 1 inch guide rods.

Steel top quality commercial weight stacks, powder coasted, balanced, fully machined surfaces.Size: 4 inch x 1 inch thick with 1 inch diameter holes. 200 pound stack in 10 pound plates, with standard 7/8 inch shaft, heavy duty spring cotter pin, high tensil laniard locking pin and 1 inch thick powder coard steel (not cast) weight plates, with press-in bushings and fits 1 inch guide rods.